Sonochemical conversion of CO2 into hydrocarbons: The Sabatier reaction at ambient conditions

In this study, we investigated an alternative method for the chemical CO₂ reduction reaction in which power ultrasound (488 kHz ultrasonic plate transducer) was applied to CO₂-saturated (up to 3%) pure water, NaCl and synthetic seawater solutions. Under ultrasonic conditions, the converted CO₂ products were found to be mainly CH₄, C₂H₄ and C₂H₆ including large amount of CO which was subsequently converted into CH₄. We have found that introducing molecular H₂ plays a crucial role in the CO₂ conversion process and that increasing hydrogen concentration increased the yields of hydrocarbons. However, it was observed that at higher hydrogen concentrations, the overall conversion decreased since hydrogen, a diatomic gas, is known to decrease cavitational activity in liquids. It was also found that 1.0 M NaCl solutions saturated with 2% CO₂ + 98% H₂ led to maximum hydrocarbon yields (close to 5%) and increasing the salt concentrations further decreased the yield of hydrocarbons due to the combined physical and chemical effects of ultrasound. It was shown that CO₂ present in a synthetic industrial flue gas (86.74% N₂, 13% CO₂, 0.2% O₂ and 600 ppm of CO) could be converted into hydrocarbons through this method by diluting the flue gas with hydrogen. Moreover, it was observed that in addition to pure water, synthetic seawater can also be used as an ultrasonicating media for the sonochemical process where the presence of NaCl improves the yields of hydrocarbons by ca. 40%. We have also shown that by using low frequency high-power ultrasound in the absence of catalysts, it is possible to carry out the conversion process at ambient conditions i.e., at room temperature and pressure. We are postulating that each cavitation bubble formed during ultrasonication act as a “micro-reactor” where the so-called Sabatier reaction -$C{O}_2+4H_2\stackrel{\mathit{Ultrasonication}}{\to }C{H}_4+2H_{2}O$ - takes place upon collapse of the bubble. We are naming this novel approach as the “Islam-Pollet-Hihn process”.     

Mechanism of BPh3-Catalyzed N-Methylation of Amines with CO2 and Phenylsilane: Cooperative Activation of Hydrosilane

BPh₃ catalyzes the N-methylation of secondary amines and the C-methylenation (methylene-bridge formation between aromatic rings) of N,N-dimethylanilines or 1-methylindoles in the presence of CO₂ and PhSiH₃; these reactions proceed at 30–40 °C under solvent-free conditions. In contrast, B(C₆F₅)₃ shows little or no activity. ¹¹B NMR spectra suggested the generation of [HBPh₃]⁻. The detailed mechanism of the BPh₃-catalyzed N-methylation of N-methylaniline ( 1 ) with CO₂ and PhSiH₃ was studied by using DFT calculations. BPh₃ promotes the conversion of two substrates (N-methylaniline and CO₂) into a zwitterionic carbamate to give three-component species [Ph(Me)(H)N⁺CO₂⁻⋅⋅⋅BPh₃]. The carbamate and BPh₃ act as the nucleophile and Lewis acid, respectively, for the activation of PhSiH₃ to generate [HBPh₃]⁻, which is used to produce key CO₂-derived species, such as silyl formate and bis(silyl)acetal, essential for the N-methylation of 1 . DFT calculations also suggested other mechanisms involving water for the generation of [HBPh₃]⁻ species.     

Facile sonochemical synthesis of rutile-type titanium dioxide microspheres decorated graphene oxide composite for efficient electrochemical sensor

In this reports the facile and green synthesis of rutile-type titanium dioxide nanoparticles decorated graphene oxide nanocomposite via the ultrasonication process (frequency: 50 kHz, Power: 100 W/cm² and Ultrasonic type: Ti-horn). Because, the sonochemical synthesis method is simple, non-explosive and harmless method than other conventional technique. Furthermore, the synthesized material was characterized by various analytical techniques including FESEM, EDX, XRD, EIS and electrochemical methods. Then, the synthesized TiO₂ MPs@GOS composite was applied for the electrocatalytic detection of theophylline (TPL) using CV and amperometric (current-time) techniques. Captivatingly, the modified sensor has excellent electrocatalytic performance with the wider linear range from 0.02 to 209.6 µM towards the determination of theophylline and the LOD and sensitivity of the modified sensor was calculated as 13.26 nM and 1.183 μA·µM⁻¹·cm⁻², respectively. In addition, a selectivity, reproducibility and stability of the TiO₂ MPs@GOS modified GCE were analyzed towards the determination of theophylline molecule. Finally, the real time application of TiO₂ MPs@GOS modified theophylline sensor was established in serum and drug samples.     

Mechanistic Aspects of a Highly Active Dinuclear Zinc Catalyst for the Co‐polymerization of Epoxides and CO2

The dinuclear zinc complex reported by us is to date the most active zinc catalyst for the co‐polymerization of cyclohexene oxide (CHO) and carbon dioxide. However, co‐polymerization experiments with propylene oxide (PO) and CO₂ revealed surprisingly low conversions. Within this work, we focused on clarification of this behavior through experimental results and quantum chemical studies. The combination of both results indicated the formation of an energetically highly stable intermediate in the presence of propylene oxide and carbon dioxide. A similar species in the case of cyclohexene oxide/CO₂ co‐polymerization was not stable enough to deactivate the catalyst due to steric repulsion.     

Photosensitive organic-inorganic hybrid structures based on porous silicon

Abstract

In this study, the photovoltaic organic-inorganic structures were created by deposition of poly(3,4-ethylenedioxythiophene) film doped by poly(styrenesulfonate) and reduced graphene oxide on the porous silicon/silicon substrate. Formation of the hybrid structure was confirmed by means of atomic-force microscopy and Fourier transform infrared spectroscopy. The current-voltage characteristics of the obtained structures were studied. It was found the increase of electrical conductivity and photo-induced signal in organic-inorganic structures. Temporal parameters and spectral characteristics of photoresponse in the 400–1100?nm wavelength range were investigated. The widening of spectral photosensitivity in a short-wavelength range due to light absorption in various layers of the multijunction structure in comparison with single crystal silicon was revealed.     

Tuning the Basicity of Cyano‐Containing Ionic Liquids to Improve SO2 Capture through Cyano–Sulfur Interactions

A new approach has been developed to improve SO₂ sorption by cyano‐containing ionic liquids (ILs) through tuning the basicity of ILs and cyano–sulfur interaction. Several kinds of cyano‐containing ILs with different basicity were designed, prepared, and used for SO₂ capture. The interaction between these cyano‐containing ILs and SO₂ was investigated by FTIR and NMR methods. Spectroscopic investigations and quantum chemical calculations showed that dramatic effects on SO₂ capacity originate from the basicity of the ILs and enhanced cyano–sulfur interaction. Furthermore, the captured SO₂ was easy to release by heating or bubbling N₂ through the ILs. This efficient and reversible process, achieved by tuning the basicity of ILs, is an excellent alternative to current technologies for SO₂ capture.     

单晶硅晶格间距的测量技术进展及应用

单晶硅晶格间距是许多重要物理常数测量的基础。本文介绍了硅晶格间距测量技术的发展历程,包括X射线干涉仪直接测量和晶格比较仪间接测量两种方法,以及影响测量结果不确定度的关键因素。得益于晶格间距测量的进展,在纳米尺度,硅晶格间距被国际计量局(BIPM)批准成为新的米定义复现形式。最后介绍了硅晶格在计量学中的应用,以及基于硅晶格实现纳米几何量测量的溯源体系的研究趋势。     

改进型单晶炉提拉系统偏心平衡研究

随着光伏行业的快速发展, 对硅单晶的品质和长晶装备的稳定性的要求也不断提高。直拉法是生产硅单晶的主要方法,通过提高单晶炉副室的高度以扩大单晶硅的生产规模。由于副室高度的大幅增加,且单晶炉提拉头质心相对于旋转轴心有一定距离,对单晶炉整体稳定性有较大影响,从而降低了单晶硅的生产质量。针对此问题,对单晶炉建立可靠的力学分析模型,采用数值仿真方法,对单晶炉整体进行动力学响应分析,计算得到副室高度增加后的单晶炉工作时中钨丝绳下端晶棒的运动规律以及最大摆动幅度,为改进设计提供依据。数值仿真分析表明提高单晶炉副室高度后,提拉头较大的质心偏心是单晶炉提拉系统发生摆动的主要原因。在此基础上提出在提拉头上添加质心调节装置,通过控制系统调节可保证提拉头质心位置在旋转轴线上以降低提拉系统的摆动。     

浮升力和流动加速对超临界CO2管内流动传热影响

基于单相流体的概念,超临界流体的异常传热行为已经被研究很多年了,但是关于其流动传热机理仍没有统一的认识.本文通过理论分析和实验研究了超临界二氧化碳在竖直管内向上流动过程中,浮升力和流动加速效应对其流动结构和传热过程的影响.结果表明,没有确凿的实验证据表明超临界流体的异常传热行为是浮升力和流动加速直接导致的,存在的估计浮升力和流动加速效应准则均是在常物性流体的基础上,做了大量假设得出的,不同的研究者采用浮升力和流动加速准则分析超临界流体的传热恶化得出的结论不一致.最后,基于拟沸腾理论分析超临界流体的传热恶化过程,提出超临界沸腾数区分了超临界流体正常传热与恶化传热的转换边界,为超临界流体流动传热研究提供新思路,超临界沸腾数对建立用于不同技术的超临界流体动力循环的最佳运行条件具有重要意义.